DIN 15018 (1984)

DIN 15018 performs the static stress check and fatigue check for the steel structures of crane and crane equipment. Fatigue calculations are performed according to the Allowable Stress Design method (ASD).

DIN 15018

To add DIN 15018 standard execute Standards - Main - Other - DIN 15018 (1984) from the ribbon:

Press to Set Standard Custom Settings

To perform the fatigue check three classifications should be defined: Weld Type, Element Group and Material Type.

Weld Type - also called Notch Case, determines which elements belong to what weld type (K0-K4 - joints affected by welding, W0-W2 - elements and joints, not affected by welding). Weld Type depends on the shape, structural design, whole pattern or type and quality of the welds.

Include Rainflow Counting - include rainflow fatigue summation check with defined result category and method from which Rainflow Counting data will be used.

Note: category options for fatigue are Weld Stress or Hot Spot Stress.

Note: this option is available only for Enterprise licensing.

Element Group - depends on the Load Spectrum and Class of Utilization (number of cycles). Can be set from B1 to B6.

Load Spectrum:

Load Spectrum			Remarks
S0	Very light	P=0	Crane by exception loaded with the working load, and as a rule, with very light loads
S1	Light	P=1/3	Crane sometimes loaded with the working load, and as a rule with loads of about 1/3 of the working load
S2	Moderate	P=2/3	Crane repeatedly loaded with the working load, and as a rule with loads between 1/3 and 2/3 of the working load
S3	Heavy	P=1	Crane frequently loaded with the working load

Class of utilization (number of cycles):

Class of utilization	Number of expected load cycles		Remarks
	Over	To...incl
N1	-	2 x 105	Irregular use with long periods of rest
N2	2 x 105	6.3 x 105	Regular use in interrupted operation
N3	6.3 x 105	2 x 106	Regular use in continuous operation
N4	2 x 106	-	Full, continuous operation

Element Group (Table 14):

Design load spectrum	Class of utilization
	N1	N2	N3	N4
S0	B1	B2	B3	B4
S1	B2	B3	B4	B5
S2	B3	B4	B5	B6
S3	B4	B5	B6	B6

Material Type - define which steel is used St37 or St52.

Standard uses material data (Yield/Tensile) in calculations. Wizard checks if the values are defined for all materials.

By default, the full model is set for the selection, but it is possible to edit the selection.

Press to define safety factors for static stress check for Individual Loads and Loads Sets:

The fatigue calculations (2..Fatigue) are performed on Load Group only, stress range from load group is required. Check "3..Fatigue Summation" performs additional calculations and sum damage from different load groups based on stress history defined in Fatigue Group.

Use Hot Spot Stress - use Hot Spot Stress results for locations defined in Weld Finder Tool or Weld Stress results in the fatigue checks.

Static Check

The allowable static stress check equal to the minimum of material yield stress and 70% of tensile strength:

For the shear direction the allowable stress is divided on √3

Fatigue Check

The Kappa factor is the ratio between the minimum and the maximum stresses

Smin and Smax - minimum and maximum values of calculated result stresses;

For K-factor [-1;0]:

For K-factor (0;1]:

Where Sf – the allowable stress fatigue when K=-1. The Stress fatigue can be set by the exact value or by setting the crane group and the weld type.

Allowable fatigue stress is divided on coefficient (depends on the direction and the weld type):

Coefficient = 1 – for the normal and equivalent stresses.

Coefficient = – for the shear stress with the weld classification K0-K4.

Coefficient =– for the shear stress the with weld classification W0-W2.

Combined utilization factor fatigue is calculated using the following formula (the sign of Ufx, Ufy and Ufz are taken into the account) :

Maximum Utilization factor fatigue: